Multi-ring burner with 6 KW
Full electronic power level regulation on 12 levels
Precision crafting of 3 mm stainless steel
For surface installation with a visible edge or for flush installation
Precise and reproducible flame size
Automatic fast ignition, electronic flame monitoring with automatic re-ignition
Simmer function for cooking on a very low output level
Can be combined perfectly with other Vario appliances of the 400 series
1 multi-ring wok burner (300 W – 6000 W), suitable for pots up to max. ø 32 cm.
Control knobs with illuminated ring, cooking zone and output level markings.
One-handed operation.
Full electronic control in 12 output levels for exact power level adjustment plus simmer function.
Automatic fast ignition.
Simmer function.
Cast pan support with flat, continuous pot surface.
Brass burner rings.
Electronic flame monitoring with automatic re-ignition.
Residual heat indication.
Safety shut-off.
Depending on the type of installation (surface-mounted or flush-mounted, with or without an appliance cover), the specific location of the cut-out and the knob positions may vary.
The drawing "Installation of the control knob" must be observed if the panel is more than 23 mm thick (there must be a recess at the rear).
If combining several Vario appliances of the 400 series, a connection strip VA 420 must be placed between the appliances. Depending on the type of installation, the corresponding connection strip must be provided.
The bearing capacity and stability, in the case of thin worktops in particular, must be supported using suitable substructures. Take into account the appliance weight and additional loads.
Additional instructions for flush installation:
Installation is possible in worktops made of stone, synthetics or solid wood. Heat resistance and watertight sealing of the cut edges must be observed. Concerning other materials please consult the worktop manufacturer.
The groove must be continuous and even, so that uniform placing of the appliance on the gasket is ensured. Do not use discontinuous lining.
The joint width may vary due to size tolerances of the combinations and of the worktop cut-out.
If installing several appliances in individual cut-outs allow for a division bar of minimum 50 mm between the individual cut-outs.
Special nozzles can be ordered as spare parts.
Plan for an electrical connection (the appliance is not operable without power supply).
Air intake from above.
No intermediate shelf required.
Rear panel and wall trims must be heat-resistant and consist of a non-flammable material.
A minimum clearance of at least 150 mm from adjacent heat-sensitive furniture or contact surfaces must be observed or thermal insulation fitted.
If operated next to the downdraft ventilation VL 414, the ventilation moulding AA 414 is recommended to ensure maximum performance of the cooktop.
With a total connected load of more than 11 kW local regulations concerning room ventilation, room size and combination of extraction or recirculation hoods must be observed.
The minimum distance between the cooktop surface and a cabinet above, out of combustible material, needs to be 70 cm.
The minimum distance to a ventilation above is shown at the planning hints for the individual ventilation product.
Appliance can be snapped into the worktop from above.
Appliance weight: approx. 14.
Total connected load gas 6.0 KW.
Total connected load electric 15.0 W.
Connecting cable 1.4 m with plug.
Kako kupiti.
Leicht kuhinje, kućne aparate ili tapacirani nameštaj možete kupiti u našem izložbenom salonu na adresi Novi Beograd, Tadije Sondermajera 11 ili popunjavanjem prijave na dole navedenoj web stranici, kontaktiranjem putem telefona +381 62 777474 ili nam pisati na info@leichtbalkan.com ili dodavanjem proizvoda do kolica i naručivanja . Naš zaposleni će vas uskoro kontaktirati da vam damo potrebne informacije.
Kada istovremeno naručite kuhinju ili tapacirani nameštaj u našem izložbenom salonu, dobijate dodatni popust na ceo asortiman kućnih aparata.
Da biste dobili individualnu ponudu za Leicht kuhinje, preporučujemo da lično posetite naš izložbeni prostor u Beogradu kako biste se upoznali sa fabričkim asortimanom. Preporucujemo da imate tehnicki nacrt sobe sa sobom zajedno sa instalacijama, ako je moguće, 3D vizuelizaciju dizajna sobe koju je napravio vaš arhitekta ili dizajner. Preliminarni trošak vaše kuhinje biće gotov za 2-3 radna dana.
Za posetu salonu, poželjno je da nas unapred obavestite o očekivanom datumu i vremenu posete.
Plaćanje
Plaćanje se vrši tek nakon dogovora o svim detaljima (vreme i mesto isporuke, priključak) nakon prijema Ponude. Prihvatanjem Ponude slažete se sa Opštim uslovima trgovine firme. Plaćanje se može izvršiti direktno u salonu Leicht Balkan na adresi Novi Beograd, Tadije Sondermajer 11, ili na račun kompanije.
Plaćanje avansa za kućne aparate vrši se u iznosu od 100% vrednosti porudžbine.
Plaćanje avansa za potvrdu porudžbine Leicht kuhinje ili tapaciranog nameštaja Het Anker vrši se u iznosu od 70% vrednosti porudžbine, a preostalih 30% potrebno je uplatiti u roku od 7 dana nakon prijema zvaničnog obaveštenja od zaposlenog u kompaniji da je roba stigla u magacin kompanije.
Vreme isporuke
Prosečno vreme isporuke*:
Leicht kuhinje – 3 meseca od datuma potvrde porudžbine u fabrici;
Tapacirani nameštaj Het Anker – 7 nedelja nakon uplate avansa;
Aparati za domaćinstvo – u zavisnosti od raspoloživosti opreme u skladištu dobavljača, od 1 nedelje do 3 meseca.
*Vremena isporuke su samo informativnog karaktera. Tačan rok isporuke biće naznačen u pojedinačnom projektu koji je pripremljen za vas.
Vremena isporuke mogu varirati zbog nepredviđenih okolnosti koje su van kontrole prodavca i biće zvanično objavljene kupcu u najkraćem mogućem roku.
Troškovi isporuke
Isporuka se vrši u dogovorenom roku nakon pune 100% uplate. Cena dostave unutar Srbije je uključena u cenu isporuke, u druge zemlje dogovara se pojedinačno.
Isporuku vrše naše ugovorena treća strana. Kada naručilac potpiše otpremnicu, prestaje odgovornost za robu od strane zaposlenih u kuriskoj službi.